DIY Geiger Counter – Planning

I’ve always wanted to have and build a Geiger Counter. This doesn’t mean I want to start experimenting with radioactive materials, I just have a general interest. At most I might collect items from thrift stores that measure higher than normal amounts of radiation. At most I wouldn’t mind sputtering the radioactive metal onto glass slides.

Found some tutorials but the most appealing to me was one built by tanner_tech featured on recently that utilized a 555 timer and a step up transformer to get the 400V. 400V across the tube allows gamma rays or beta particles to start the ionization completing the circuit.

After settling on a design I purchased 3 Russian Geiger tubes CI-3BG / SI-3BG from ebay link here. They sent me 4…. Win!

I want to take this one step further and have the data output to a screen and log that data rather than just make noise. So the end result will be an Arduino or Raspberry Pi to control the Geiger Counter. I just need to learn the best way to take the 400v pulses and turn that into something a microcontroller can safely read. If you know the best way to do this please contact me.

After a few corrections to the circuit to level the voltage to a consistent 400V I believe I’m ready to begin building the initial geiger counter. That is after I get a few other projects out of the way. Being able to simulate the circuit, as shown below, was a huge help.

Parts List

  • 1x 555 timer
  • 2x 47k resistors
  • 1x 22nF capacitor
  • 1x 2.2nF capacitor
  • 1x 1k resistor
  • 1x 8:800 ohm transformer
  • 1x Any N-channel MOSFET
  • 2x 1n4007 diode (on regulator)
  • 2x 100nF 500 volt capacitor (on regulator)
  • 4x 100 volt zener diode
  • 1x Geiger tube (in simulation I’m using a lamp)

If built from scratch, buying parts in small quantities each unit is estimated to cost around $12-$15 so not bad at all.

Recreation of the circuit with simulation on EveryCircuit

Friggin loving Every Circuit! Visually seeing the results and being able to tweak values during live simulation is beautiful.

Links to original design

Tanner_tech’s Instructables

RC Truck With Electromagnetic Accelerator Turret

There are many different types of RC cars on the market today, that come in all different price ranges and can do all kinds of different things. In this instructable, I will not only be showing you how to build an RC military truck kit that I recieved in the mail, but how to build your own DC motor...
By: tanner_tech


Stepper Motor Key-tar: a New Kind of Instrument

Have you ever started a printer, and heard the various sounds it creates? Wouldn't it be awesome to create a whole instrument that plays these retro printer sounds on actual printer parts? Well, you're in luck. In this Instructable, I will show you how to build the Stepper Motor Keytar. This rec...
By: tanner_tech


DIY Induction Heater

When you think of a way to heat up a metal object, you think of fire -right? Fire is an inefficient, old fashioned, and slow way to heat up metal objects. It wastes lots of energy as heat and creates lots of dirty smoke. Well, what if you could have a way to heat up metal objects that solves all ...
By: tanner_tech


12 Volt 50 Amp Bench Integrated Power Supply

A lot of the power supplies that you see on the internet that can only supply 12 volts do not pack very much power. They can only supply a few amps. Some of my projects required a lot more current than most ATX or other bench power supplies could handle! What if I told you that you could build an...
By: tanner_tech


Electromagnetic Fidget Spinner Accelerator

Fidget Spinners are little plastic toys with a bearing in the center. They are fun for a little bit, but get boring after a while due to their slow spinning speeds. There are ways to make them spin faster, but these methods involve using a bulky air compressor or an expensive can of compressed air...
By: tanner_tech


DIY Cathode Ray Tube: Interacting With Electrons

Electrons: they are all around us, but we cannot really see or interact with them. Luckily, there is a device that will let you. A cathode ray tube, or CRT, is a glass tube with electrodes on either end. When there is a vacuum drawn and a high voltage across the two electrodes, a cathode ray form...
By: tanner_tech