Ep 2: Bronzeville Episode 1 Coverage

Welcome to episode 2 of the Bronzeville FanCast covering episode 1 of the Bronzeville Series. You’re hosts are MickGinger, DW Witch Doctor and MrRedBeard. We will be covering every new release of Bronzeville.

Be sure to check out our Bronzeville FAQ.

RSS Feed for the Bronzeville FanCast – http://www.mickred.com/category/bronzeville/feed/

Aunt Sally’s Policy Players’ Dream Book & Policy Pete’s Dream Book

Bronzeville: Black Chicago in Pictures, 1941 – 1943

 

What did you hear? Tell us on twitter!

Check back here for episodes, articles and hopefully interviews

Music Credits:

Excerpt of Louis Armstrong’s cover of Old Man Mose which is Public Domain which was remixed

Microwave Plasma Chamber – Part 2 – RF Energy Shielding Primer

RF Shielding Primer

There’s a lot of in-depth overview random basic RF information. With that said I don’t mind getting into the details because this information will help keep me safe while I perform experiments in the future.

Magnetron
Magnetron

A magnetron generates large amounts of RF energy and emits that energy as an antenna pumped through a wave guide. Most microwaves transmit/operate at 2.45GHz. Unless something is wrong with your microwave or you have taken it apart like I will be doing the RF energy, 2.45GHz, transmission is contained within your microwave using a Faraday cage. On your right is an example of a crude Faraday cage. While crude this mesh size would probably be safe to use for 2.4GHz.

Photo from www.physics.montana.edu
Radio in a Faraday Cage photo from http://www.physics.montana.edu/demonstrations/video/5_electricityandmagnetism/demos/radioinfaradaycage.html

A microwave oven works by pumping a lot of RF energy into an enclosure where it bombards the molecules of food or whatever you have put in your microwave. This RF energy is not in a straight line but is guided through a wave guide then and then bounced off the metal walls of the inside of the microwave. The RF energy then vibrates the molecules which creates heat. This is like when you rub your hands together (friction) and they get warm but on a molecular level. What I don’t want is my molecules to get vibrated.

The Faraday cage is made up of the mesh in the window as well as the metal case which share a chassis ground. The mesh in the window blocks the the RF because the mesh size is smaller than the wavelength of 2.45GHz/2450MHz/2450000000Hz. If the mesh size is lower than the nominal wavelength the mesh should be effective. Look at the list below to see what the wavelengths in size is. For this project I plan on using the RF blocking glass that I obtained samples of from Viracon which is way different than a Faraday cage but same principle. You can see the article I linked to but I also included an image here.

  • Full Wavelength = 12.23643cm/122.3643mm = 0.1223643m
  • Half Wavelength = 6.118215cm/61.18215mm
  • Quarter Wavelength = 3.0591cm/30.591075mm

You can calculate the wavelength using the formula 𝜆 = c/𝑓 or 0.1223640816326531 = 299792000/2450000000

𝑓 = frequency in hz, = speed of light in mps 299792000, 𝜆 = Wavelength in meters

N5JLC is my math right?

So basically if my mesh is smaller than 30mm, if I’m right, I should be protected. I plan to use the glass but if needed I will use hardware cloth.

RF Meters

In order to protect myself and nearby electronics I want to monitor external and internal RF to ensure there is not leakage. RF Meters in general are not that difficult to build but ones that cover the 2.4GHz range require a bit more than a germanium diode and multimeter. In short you’ll probably see a 2.4GHz RF Meter project coming soon. Below are some RF Meter projects but if you know of any please let me know.

Frequency Spectrum Chart

Frequency Spectrum

Symbols and Values

  • 𝑓 = frequency in hz
  • c = speed of light in meters per second (mps) 299792000
  • 𝜆 = Wavelength in meters

Microwave Plasma Chamber – Part 1 – The Plan

 

Microwave Plasma Chamber – Part 1 – The Plan

Normally I throw together a project with rough notes, research along the way, then after half attempts/failures I get around to cooking that down to a post on here. This time you will get everything. With this project I will be posting my ideas, planning, results of research and the project in stages. Here’s my initial idea written out and some really rough ideas thrown on paper. This has been a project I’ve been wanting to do for some time now and have been talking about it forever.

Roughed together a drawing of my ideas and what I think will work for this project. No measurements in mind while throwing ideas on paper.

What I want is a chamber with viewing windows to see the plasma when it’s created. In addition to the view windows and enclosure I will need a power supply to drive this thing.

 

 

Took my drawing and opened SketchUp with considerations for what measurements I do have. As I type this staring at my digital drawing already considering separating the power supply making it usable for other projects in the future. It would be cool to have a high voltage isolation transformer for things like a Jacobs Ladder or an arc furnace.

Regardless of the power supply what I have in mind here is the plasma chamber with viewing windows which are 12 inches square. I plan to have a microcontroller monitor and remotely turn on or more importantly off the chamber.

 

The main chamber will have the magnetron from a microwave mounted inside of it with a metal housing around it and it’s electronics to protect them. The antenna portion of the magnetron will rest inside a waveguide (horn) that points at the center of the chamber. This directed energy will excite particles creating plasma. I probably need to consider a way to draw a vacuum inside the chamber for later experiments.

I plan to use parts of the original microwave casing and sheet metal for the housing. If I need more material I might scrap old PC cases. To help minimize RF leakage I am considering using aluminum duct tape and angled aluminum.

Magnetron Wiring

Need to look at the manufacturer specifications and double check my work but I think this how the magnetron wiring is done minus the existing controls.

PreRelease Late Night EditRemember how I said I’d share everything? Well do you see where on the capacitor I have an element leading to an X? I think I already screwed up and that is supposed to be a diode going to chassis ground. 

I also have this crazy idea in the back of my head thinking of using pulse width modulation to have greater control of the RF output. That may be total non-sense but the implications could maybe be cool.

RF meters will be needed to monitor interior and exterior RF levels. I plan to build at least 2 of them and will post that project soon. I will post more about the RF energy in my next post of this project.

Click here to browse through posts written about my interests in Microwave Projects

Ep 1: Bronzeville Preview Coverage

Welcome to episode 1 of the Bronzeville FanCast. You’re hosts are MickGinger, DW Witch Doctor and MrRedBeard. We will be covering every new release of Bronzeville. Forgive us for the audio quality due to technical issues. The audio was cleaned up quite a bit and we promise to strive for better every time.

Be sure to check out our Bronzeville FAQ.

Click here to listen to the Bronzeville Series Preview

We broke it down so if you haven’t, take a listen and see what all you hear.

  • When – June 11 1945
  • Where – Bronzeville, Chicago
  • Numbers, Policy Wheel
  • Characters we heard directly or were name dropped
  • Numbers games are helping pay for the hospital, library
  • Story components are going to include love, crime and art

What did you hear? Tell us on twitter!

Listen to our interview with Kc Wayland about Bronzeville

Check back here for episodes, articles and hopefully interviews

Music Credits:

Excerpt of Louis Armstrong’s cover of Old Man Mose which is Public Domain which was remixed

SainSmart L293D Fail!!

This is a project in the works but what the hey here’s sort of a preview. The plan is to use 2x 400MHz transceivers via 2x arduinos to control the motors on this RC car. I’ve already taken the original controller board out of the car and made room for the new components.

So I was sitting here setting up a SainSmart L293D Motor Driver using specs and guidance from Adafruit and either I missed something or the information is wrong. At 3.5vdc it works but could be pushed so I grabbed an 18vdc drill battery thinking it would be fine because the circuit as quoted from Adafruit below states that it is rated to 25vdc.

25vdc my foot cause as soon as I set it up smoke popped and I smell burning on both the arduino and motor controller. It still seems to work but surely problems will rear their head.

Just ordered better motor controllers (same as the one used in my R2D2) and 18650 battery holders. Wouldn’t be so bad but I think the arduino board is fried.

Just so anyone else is aware this is the link I purchased my L293D from on Amazon. I already complained but I’m not the first to do so.

4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, 4.5V to 25V

https://learn.adafruit.com/adafruit-motor-shield/overview

Arduino and UV Lights for Glow in the Dark Decorations

My wife, MrsRedBeard, made some glow in the dark heads for Halloween decorations. They glowed but very dim and not for very long so why not kick it it up with UV lights. But why stop there when there’s an Arduino laying around?

Using the Arduino I made it so that the lights fade in to brightness, blink, hold for a few seconds then turn off for a while and loop.  The code for this can be found on GitHub.

I’m not getting real in-depth on how to do this because most of it is really basic. If you want additional information just Contact us.

Parts / Materials

  • Arduino
  • UV LEDs from Adafruit
  • An old CAT 5 cable
  • 2 screw terminals
  • 2x 2N3904 Transistors
  • Wire
  • A salvaged project box
  • Styrofoam ring cut in half
  • A empty circuit board

Pictures of the project

Bronzeville Primer

Bronzeville announced to release on February 7th!

Actual Bronzeville Art for Show - https://twitter.com/BronzevilleShow

Update: Be sure to check out our Bronzeville FAQ.

What to possibly expect?

Bronzeville, written by Josh Olson, is directed by Larenz TateLaurence Fishburne and Kc Wayland. We sat down with Kc Wayland and got the chance to talk about Bronzeville to find out more details during episode 72 of the We’re Alive FanCast.

Bronzeville’s cast include Larenz Tate as Jimmy Tillman, Laurence Fishburne as Curtis “Eyeball” Randolph, Tika Sumpter as Lisa Copeland, Tracee Ellis Ross as Anna Copeland, Wood Harris as Everett Copeland, Omari Hardwick as Jesse Copeland and Cory Hardrict as Casper Dixon. Source GlobalGrind.com

So I shouldn’t have to say it but this star studded cast is huge for an audio drama and is a first in a very long time.

Located in the Douglas community of South Side Chicago lays Bronzeville, also known as Known as Black Metropolis, the site of Chicago’s version of the Harlem Renaissance. Home to many famous African-Americans to include Louis ArmstrongNat “King” Cole, Ida B WellsGwendolyn BrooksRichard Wright, Bessie ColemanAndrew Foster and many more.

During the early 20th century roughly 6 million African Americans fled from oppression faced in the south. This event is referred to as the Great Migration.  During this time thousands of families and individuals sought out a better life in Chicago.

The focus of the Bronzeville Audio drama, as much as we know, is the Numbers Games during the 1940’s. Numbers/Policy Game or Numbers/Policy Racket is an illegal lottery where the person playing attempts to pick numbers that will match a random number drawn at a later time.

A few behind the games in Bronzeville were Eddie Jones, Theodore Roe, John V. “Mushmouth” Johnson, but considering the long History of Organized Crime in Chicago there are many more. In many instances the Mafia either attempted to or completely took over the Numbers Games but not without a fight. Eventually these forms of gambling evolved into legal state lotteries.

How big were the Numbers Games? Eddie Jones and his brothers at one point were making more than 180k per week which is way more than enough to draw attention from law enforcement and other criminal elements.

Gangster Audio Drama!!

Listen to our interview with Kc Wayland about Bronzeville

Check back here for episodes, articles and hopefully interviews

DIY DeadMau5 Head on a Budget

Here’s a brief run down on a DIY DeadMau5 head or helmet that I built with my son for Halloween.

Materials

Estimated Cost $33.48

Tools

Cut the half circles to give room for the neck. Magnets hold the spheres together. Put the half spheres together and mark evenly spaced marks around on both spheres to recess 2 sets of magnets total into each side. Don’t do like me and try and use E6000 cause it melts styrofoam, use hot glue just don’t let it get real hot.

Next for the mouth and ears. Use the paper DeadMau5 Mouth template, cut slits into the paper to get the templates to lay evenly and flat onto the surface of the sphere and tape it. Mark lines lightly with a pencil then cut using the hot knife in a well ventilated area. Be careful because the foam melts easy. Use the paper DeadMau5 Ear template to mark and cut the foam for the ears. Note that you will have to cut a curve into the base of the ears to get it to lay flush.

Now for the eyes. Take the 2 Dollar Store Touch Lights apart. You are wanting the dome that acts as a light diffuser. If you get lucky you might be able to use the leds. There will be lip around the outside edge of the dome that will need to be cut off and we used a hot knife for this.

Trace where the ears will be mounted on the sphere then cut/push a recess. Use black hot glue to fix the ears to the sphere. Paint the sphere and ears using acrylic paint. We applied 2 coats to get a good black color applied. Now take the domes you cut out and trace where you want the eyes. Cut/push in the outlines to better recess the domes. In the center of these eye traces you will want to make holes just smaller than the LED you acquired. Hot glue with black glue sticks the eyes. Make Xs on the eyes using electrical tape. Trace the mouth onto the fabric using the DeadMau5 Mouth template tracing slightly larger than the original. Using the black hot glue attach the fabric inside the mouth.

Now it’s time to wire up the LEDs for the eyes. This is pretty simple so I’m not going to post additional info unless asked. Amazon failed to deliver the Red El Wire on time for Halloween but we plan to add that soon. The Red El Wire will outline the ears and mouth.

DIY 100 Watt Bluetooth Speaker

There’s a trend of bluetooth speakers built into suitcases, ammo cans and other unconventional containers. These things sell for $300 or more which is quite a bit more than what it costs to build them. I will break down the parts, sources and their prices. This project was very easy and very affordable.

If you want a custom speaker built just contact us!

Parts

Total cost for one $38.87 (only used one of the speakers)

I found this train case on the side of the road. I stripped out the interior of the case and cleaned it up.

 

I used a template I found online for the Planet Audio TQ573 5×7 speaker to cut out the hole.

The amp is rated at 50 watts per channel and the speaker is rated at 100 watts. This build only uses one speaker so I bridged the amp to output 100 watts. This amp will run off 12vdc so a portable version would be an easy build.

Speaker mounted and working. It can get pretty loud and sounds great.

 

RedBeard’s Donnie Darko Mask

Favorite moment of the Donnie Darko mask
Favorite moment of the Donnie Darko mask

I’ve been wanting to make a Donnie Darko Frank the Bunny mask for some time now and finally got around to doing before this last Halloween. Disclaimer I’m no sculptor and have no experience with this. Definitely not perfect and I’m going to retry for something better later but I’ll share anyways.

 

 

This was a ton of fun to do but I think I might take some art classes at the AR Innovation Hub, a local maker space, soon.

Materials

I used a combination of paper mache and paper mache clay to make this mask. Paper mache clay is awesome!! I started with a styrofoam form and a blank plastic mask (that was too small).

Cara Brookins has a write up on paper mache clay. Cara is an author and super mom who I hope to interview after reading a few more of her books. I had the pleasure of meeting Cara a few years ago at River City Comic Con.

 

Errors

As you browse through the progress you’ll notice I started off with an uneven form and it never got better. I thought I’d fill in the lower jaw area to make the mask fill the outline of the printed mask but then removed it with haste. I also found out late that the paper mache clay needs to be kneaded and worked for a while before it becomes pliable. The mask ended up being a bit small but weighed a ton like hurt your neck ton.

I learned a lot from this project. I’m open to any tips you might have for the paper mache clay and sculpting in general.

 

 

 

 

 

Mask from the movie no comparison